多选题What are two ways that a valid IBGP peering session can be configured?（）Avia the accept x.x/y commandBvia TCP reachable physical interface addressesCvia remote loopbacks with the local-address commandDvia UDP with the neighbor x.x.x.x command at the gr

题目

多选题

What are two ways that a valid IBGP peering session can be configured?（）

via the accept x.x/y command

via TCP reachable physical interface addresses

via remote loopbacks with the local-address command

via UDP with the neighbor x.x.x.x command at the group level

参考答案和解析

正确答案： D,C

解析：暂无解析

更多“多选题What are two ways that a valid IBGP peering session can be configured?（）Avia the accept x.x/y commandBvia TCP reachable physical interface addressesCvia remote loopbacks with the local-address commandDvia UDP with the neighbor x.x.x.x command at the gr”相关问题

第1题

Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs()。A.a switch with a trunk link that is configured between the switchesB.a router with an IP address on the physical interface that is connected to the switchC.a switch with an access link that is configured between the switchesD.a router with subinterfaces configured on the physical interface that is connected to the switch

点击查看答案
第2题

Which three statements about the Cisco MPLS TE Fast Reroute （FRR） process are true？（）A、TE tunnels that are configured with the FRR option cannot be used as backup tunnels.B、TE tunnels that are configured with the FRR option can be used as backup tunnels.C、The backup tunnel that is used to protect a physical interface must have a valid IP address configured.D、Interfaces must use MPLS global label allocation.E、The source IP address of use backup tunnel and the merge point （MP） should not be reachable.

点击查看答案
第3题

Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。A、a switch with a trunk link that is configured between the switchesB、a router with an IP address on the physical interface that is connected to the switchC、a switch with an access link that is configured between the switchesD、a router with subinterfaces configured on the physical interface that is connected to the switch

点击查看答案
第4题

What is the main reason for using the "ip ips deny-action ips-interface" IOS command？（）A、 To selectively apply drop actions to specific interfacesB、 To enable IOS to droptraffic for signatures configured with the Drop actionC、 To support load-balancing configurations in which traffic can arrive via multipleinterfaces D、 This is nota valid IOS command

点击查看答案
第5题

What are two ways that a valid IBGP peering session can be configured?（）A、via the accept x.x/y commandB、via TCP reachable physical interface addressesC、via remote loopbacks with the local-address commandD、via UDP with the neighbor x.x.x.x command at the group level

点击查看答案
第6题

Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）A、Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transport data.B、Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP to transport packets.C、There is no way to make BGP work across a firewall without special configuration， so there is no simple test that will show you if BGP will work or not， other than trying to start the peering session.D、There is no way to make BGP work across a firewall.

点击查看答案
第7题

Two routers configured to run BGP have been connected to a firewall，one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer，including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）A、Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall.If telnet works，BGP will work，since telnet and BGP both use TCP to transport dataB、Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall.If you can ping between them，BGP should work，since BGP uses IP to transport packetsC、There is no way to make BGP work across a firewall without special configuration，so there is no simple test that will show you if BGP will work or not，other than trying to start the peering sessionD、There is no way to make BGP work across a firewall

点击查看答案

多选题What are two ways that a valid IBGP peering session can be configured?（）Avia the accept x.x/y commandBvia TCP reachable physical interface addressesCvia remote loopbacks with the local-address commandDvia UDP with the neighbor x.x.x.x command at the gr

题目

参考答案和解析

更多“多选题What are two ways that a valid IBGP peering session can be configured?（）Avia the accept x.x/y commandBvia TCP reachable physical interface addressesCvia remote loopbacks with the local-address commandDvia UDP with the neighbor x.x.x.x command at the gr”相关问题

第1题

第2题

第3题

第4题

第5题

第6题

第7题

相关内容