单选题If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?（）A area IDB router IDC loopback addressD IP address of interface on broadcast network

题目

单选题

If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?（）

area ID

router ID

loopback address

IP address of interface on broadcast network

更多“单选题If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?（）A area IDB router IDC loopback addressD IP address of interface on broadcast network”相关问题

第1题

A new network has been configured using OSPF as the routing protocol. With which network type will OSPF establish router adjacencies but not perform the DR／BDR election process?()A. point-to-pointB. Backbone area 0C. Broadcast multicastD. Non-broadcast multi-accessE. The DR/BDR process is done for all interface types

点击查看答案
第2题

Under which network type circumstance would an OSPF router establish router adjacencies while not performing the DR／BDR election process?()A. Point-to-pointB. BroadcastC. Non-broadcast multi-accessD. Backbone area 0E. None of the above

点击查看答案
第3题

OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）A. The ip ospf network broadcast command should be configured on each Frame Relay interfaceB. The ip ospf network non -broadcast command should be configured on each Frame Relay interfaceC. Th e ip ospf priority value on the spoke routers should be set to 0D. The ip ospf priority value on the hub router should be set to 0E. The neighbor command should be configured under the OSPF routing process on all routers

点击查看答案
第4题

If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()A. the IP address of the first Fast Ethernet interfaceB. the IP address of the console management interfaceC. the highest IP address among its active interfacesD. the lowest IP address among its active interfacesE. the priority value until a loopback interface is configured

点击查看答案
第5题

The OSPF process has been started and the networks have been configured for Area 0 as shown in the diagram. The network administrator has several options for configuring RouterB to ensure that it will be preferred as the designated router (DR) for the 172.16.1.0 /24 LAN segment. What configuration tasks could be used to establish this preference (Choose three.)（）。A.Configure the priority value of the Fa0/0 interface of RouterB to a higher value than any other interface on the Ethernet network.B.Change the router id of Router B by assigning the IP address 172.16.1.130/24 to the Fa0/0 interface of RouterB.C.Configure a loopback interface on RouterB with an IP address higher than any IP address on the other routers.D.Change the priority value of the Fa0/0 interface of RouterB to zero.E.Change the priority values of the Fa0/0 interfaces of RouterA and RouterC to zero.F.No further configuration is necessary.

点击查看答案
第6题

Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR and require static OSPF neighbor definition?（）A、ip ospf network broadcastB、ip ospf netw ork non - broadcastC、ip ospf network point - to - multipointD、ip ospf network point - to - multipoint non - broadcast

点击查看答案
第7题

If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）A、the IP address of the first Fast Ethernet interfaceB、the IP address of the console management interfaceC、the highest IP address among its active interfacesD、the lowest IP address among its active interfacesE、the priority value until a loopback interface is configured

点击查看答案

单选题If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?（）A area IDB router IDC loopback addressD IP address of interface on broadcast network

题目

更多“单选题If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?（）A area IDB router IDC loopback addressD IP address of interface on broadcast network”相关问题

第1题

第2题

第3题

第4题

第5题

第6题

第7题

相关内容