OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What sho

题目

OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）

A. The ip ospf network broadcast command should be configured on each Frame Relay interface

B. The ip ospf network non -broadcast command should be configured on each Frame Relay interface

C. Th e ip ospf priority value on the spoke routers should be set to 0

D. The ip ospf priority value on the hub router should be set to 0

E. The neighbor command should be configured under the OSPF routing process on all routers

参考答案和解析

参考答案：C

更多“OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active ”相关问题

第1题

Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router) network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? （）A.FastEthernet0 /0B.FastEthernet0 /1C.Serial0/0D.Serial0/1.102E.Serial0/1.103F.Serial0/1.104

点击查看答案
第2题

Which two statements are correct about configuring AutoQoS on a Cisco router？（）A、 AutoOoS can be implemented on only one side of a link.B、The interface does not have to have an IP address associated with it.C、The AutoOoS feature cannot be configured on a Frame Relay DLCI if a map class is attached to the DLCI.D、In a Frame Relay network， AutoOoS cannot be configured if a DLCI is already assigned to the Frame Relay subinterface

点击查看答案
第3题

When should traffic shaping be implemented on Frame Relay PVCs？（）A、When you want to drop excess traffic above the CIRB、When there is a speed mismatch between the central site and the remote siteC、When using Frame Relay SVCsD、When over-subscribing the central site linkE、When LLQ is implemented on the Frame Relay PVCF、When Multilink PPP LFI is implemented on the Frame Relay PVC

点击查看答案
第4题

A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）A、The central site router has 100 fully adjacent neighborships with the 100 branchesB、The central site router has neighborships with all branch routers, but fully adjacent neighbors with only two branchesC、The central site router has a neighborship with the Frame Relay switcHD、None of the other answers is correct

点击查看答案
第5题

EIGRP has been configured to operate over Frame Relay multipoint connections. What should the bandwidth command be set to?（）A、the CIR rate of the lowest speed connection multiplied by the num ber of circuitsB、the CIR rate of the lowest speed connectionC、the CIR rate of the highest speed connectionD、the sum of all the CIRs divided by the number of connections

点击查看答案
第6题

Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）A、frame - relay map commands on R3 - R10 referencing the other routers in this groupB、Nine OSPF neighbor commands on each routerC、Nine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10D、R1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRE、R3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR

点击查看答案
第7题

The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）A、The Gallant router has the wrong LMI type configuredB、Inverse ARP is providing the wrong PVC information to the Gallant routerC、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandD、The frame-relay map statement in the Attalla router for the PVC to Steele is not correctE、The IP address on the serial interface of the Attalla router is configured incorrectly

点击查看答案

OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active

题目

参考答案和解析

更多“OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active ”相关问题

第1题

第2题

第3题

第4题

第5题

第6题

第7题

相关内容