A. show interfaces serial 0/0
B. show running-config
C. show version
D. show controllers serial 0/0
E. show ip interface
F. show line serial 0/0
There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:From your observations of the above exhibit, what is the underlying cause of the problem?()A. The loopback is not set.B. The serial cable is faulty.C. The subnet mask is not configured properly.D. The IP address is not configured properly.E. The Layer 2 frame types are not compatible.F. The keepalive setting is not configured properly.
点击查看答案
Part of the configuration files for routers testking1 and testking2 are displayed below:If you were to enter the "show interface serial 0" command on router testking1,which of the following will be displayed?()A. Serial 0 is down, line protocol is downB. Serial 0 is up, line protocol is upC. Open: IPCP, CDPCPD. LCP closedE. LCP open
Refer to the exhibit.The network administrator is in acampus building distant from Building B.WANRouter is hosting a newly installed WAN link on interface S0/0.The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface.How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner?()A.Telnet to WANRouter and execute the command show interfaces S0/0B.Telnet to WANRouter and execute the commandshow processes S0/0C.Telnet to WANRouter and execute the command show running-configurationD.Telnet to WANRouter and execute the command show controller S0/0E.Physically examine the cable between WANRouter S0/0 and the DCE.F.Establish a console sessionon WANRouter and execute the command show interfaces S0/0
Usetheoutputfromtheroutershowninthegraphicabovetodeterminewhichofthefollowingarecorrect.()A.Router John uses alink-state routing protocol.B.Router John will receive routing updates on the Serial0/0 interface.C.Router John will receive routing updates on the Serial0/1 interface.D.Router John will send routing updates out the Serial0/0 interface.E.Router John will send routing updates out the FastEthernet0/0 interface.F.Router John will send routing updates out the Serial0/1 interface.
The network administrator is in a campus building distant from Building B. WANRouter is hosting a newly installed WAN link on interface S0/0. The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface. How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner()。A.Telnet to WANRouter and execute the command show interfaces S0/0B.Telnet to WANRouter and execute the command show processes S0/0C.Telnet to WANRouter and execute the command show running-configurationD.Telnet to WANRouter and execute the command show controller S0/0E.Physically examine the cable between WANRouter S0/0 and the DCEF.Establish a console session on WANRouter and execute the command show interfaces S0/0
Use the output from the router shown in the graphic above to determine which of the following are correct.()A. Router John uses a link-state routing protocol.B. Router John will receive routing updates on the Serial0/0 interface.C. Router John will receive routing updates on the Serial0/1 interface.D. Router John will send routing updates out the Serial0/0 interface.E. Router John will send routing updates out the FastEthernet0/0 interface.F. Router John will send routing updates out the Serial0/1 interface.
Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?()A、show interfaces serial 0/0B、show running-configC、show versionD、show controllers serial 0/0E、show ip interfaceF、show line serial 0/0