将Ciseo6500第4模块第1端口的通信方式设置为半双工,第2~24端口的通信方式设置为全双工,以下交换机的端口配置,正确的是( )。
两台交换机相连,要求两个连接端口工作在全双工通信方式下。若端口的通信方式为默认的duplex auto时,有时会出现大量丢包现象。这时,需要重新配置端口的通信方式。其正确的配置语句是______。A.duplexfull duplexhalfB.duplexhalf duplexfullC.duplexhalf duplexhalfD.duplexfull duplexfull
点击查看答案
将Cisco 6500第4模块第1端口的通信方式设置为半双工,第2~24端口的通信方式设置为全双工,以下交换机的端口配置,正确的是A)Switch-6500> (enable) set interface duplex 4/1 halfSwitch-6500> (enable) set interface duplex 4/2-24 fullB)Switch-6500> (enable) set port 4/1 duplex halfSwitch-6500> (enable) set port 4/2-24 duplex fullC)Switch-6500> (enable) set port duplex 4/1 halfSwitch-6500> (enable) set port duplex 4/2-4/24 fullD)Switch-6500> (enable) set port duplex 4/l halfSwitch-6500> (enable) set port duplex 4/2-24 full
交换机端口可以分为半双工与全双工两类。对于100Mbps的全双工端口,端口带宽为A.100MpbsB.200MbpsC.400MpbsD.800Mpbs
将Catalyst 6500交换机第3个模块的端口1~端口8设置为全双工通信方式,正确的配置语句是______。A.Switch-PHY-6500(config-if)#duplex fullB.Switch-PHY-6500(config-if)#duplex 3 1-8 fullC.Switch-PHY-6500>(enable) set port duplex 3/1-8 fullD.Switch-PHY-6500>(enable) set port duplex 3 1-8 full
在默认情况下,交换机刚加电启动时,每个端口都要经历生成树的四个阶段,它们分别是:阻塞、侦听、(6)、(7)。2.根据需求,需要将Swl交换机的端口1~20设置为快速端口,完成以下配置。Swl(config) interface range fastethernet 0/1-20 //进入组配置状态Swl(config-if-range) (8) //设置端口1~20为快速端口
两台交换机相逢,要求两个连接端口工作在全双工通信方式下,若端口的通信方式为默认的duplexauto时,有时会出现大量丢包现象,这时,需要重新配置端口的通信方式,其正确的配置语句是______。A.duplex full duplex halfB.duplex half duplex fullC.duplex half duplex halfD.duplex full duplex full
将Cise0 6500第4模块第1端口的通信方式设置为半双工,第2-24端口的通信方式设置为全双工,以下交换机的端口配置,正确的是( )。A.Switch-6500>;(enable)set interface duplex 4/1 halfSwitch-6500>;(enable)set interface duplex 4/2-24 fullB.Switch-6500>;(enable)set port 4/1 duplex halfSwitch-6500>;(enable)set port 4/2-24 duplex fullC.Switch-6500>;(enable)set port duplex 4/1 halfSwitch-6500>;(enable)set port duplex 4/2-4/24 fullD.Switch-6500>;(enable)set port duplex 4/1 halfSwitch-6500>;(enable)set port duplex 4/2-24 full