A router has been configured with the authentication order settings shown below: [edit] user@host# show system authentication-order authentication-order [radius tacplus password]; The router also has a local database that contains the user lab with passw

题目

A router has been configured with the authentication order settings shown below: [edit] user@host# show system authentication-order authentication-order [radius tacplus password]; The router also has a local database that contains the user lab with password lab123. What would happen if both the RADIUS and the TACACS servers respond with a reject for user lab?（）

A、The user lab will not be able to login.
B、The user lab will be authenticated against the local database and will be able to login.
C、The user will be able to login only if tries to login as the root user.
D、The user lab will receive an error message indicating the username and password provided could not be found on the radius and tacacs servers.

参考答案和解析

正确答案:B

更多“A router has been configured wi”相关问题

第1题

A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router

点击查看答案
第2题

Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）A、Subnet numberB、Next - hop router IP address of the routeC、Whether the route is an E1 or E2 routeD、The ro ute's tagE、The number of router hops between the router and the subnet

点击查看答案
第3题

Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）A、 To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.B、 The default priority of a router is zero （0）.C、 The no standby priority command assigns a priority of 100 to the router.D、 Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.E、 When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.

点击查看答案
第4题

The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）A、The Gallant router has the wrong LMI type configuredB、Inverse ARP is providing the wrong PVC information to the Gallant routerC、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandD、The frame-relay map statement in the Attalla router for the PVC to Steele is not correctE、The IP address on the serial interface of the Attalla router is configured incorrectly

点击查看答案
第5题

How can an administrator determine if a router has been configured when it is first powered up?（）A、A configured router prompts for a passwordB、A configured router goes to the privileged mode promptC、An un configured router goes into the setup dialogD、An un configured router goes to the enable mode prompt

点击查看答案
第6题

A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B、 When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E、None of the other answers is correct.

点击查看答案
第7题

A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）A、172.16.0.1/23B、172.16.1.1/26C、172.16.1.1/24D、172 .16.0.255/23E、None of the other answers is correct.

点击查看答案

A router has been configured wi

题目

参考答案和解析

更多“A router has been configured wi”相关问题

第1题

第2题

第3题

第4题

第5题

第6题

第7题

相关内容